VeraSeq 2.0 High-Fidelity DNA Polymerase

• OEM by QIAGEN offers customized bulk manufacturing of this enzyme
• Extends 1 kb in 15 seconds
• 50x greater fidelity than Taq DNA Polymerase
• Strong proofreading activity (3'→5' exonuclease activity)
• Functions in Mg²+ concentrations 1.5 to 3.0 mM
• Available in low glycerol or hot start formulations

VeraSeq 2.0 High-Fidelity DNA Polymerase is an engineered, ultra-thermostable polymerase that delivers industry-leading speed, fidelity and robustness to PCR amplification. The novel enzyme that can extend a kilobase of sequence in 15 seconds and with an accuracy 50 times higher than Taq DNA Polymerase.

The enzyme is supplied in 20 mM Tris-HCl, 100 mM KCl, 1 mM DTT, 0.1 mM EDTA, Stabilizer and 50% glycerol; pH 7.4 at 25°C.

VeraSeq 2.0 High-Fidelity DNA Polymerase is supplied with 5x VeraSeq Buffer II (cat. no. P7102) and 5x VeraSeq GC Buffer (cat. no. B7130).

Ask about low glycerol or hot-start formulations.

Polymerase properties
Extension rate: 15 seconds per kb at 72˚C
Proofreading (3'→5' exo): Yes, strong
Nick-translation (5'→3' exo): No
Fidelity: >50x higher than Taq DNA Polymerase
Strand displacement: No
Thermostability: Highly thermostable
Able to extend an RNA primer: No
Extends from a nick: No
Generate blunt-end products: Yes
Uracil read through: No

• Storage temperature: –25°C to –15°C

Source of recombinant enzyme protein
The protein is produced by a recombinant E. coli strain carrying the engineered VeraSeq 2.0 gene.

Unit definition:
One unit is defined as the amount of enzyme required to incorporate 10 nmoles of dNTPs into acid-insoluble form at 74°C in 30 minutes.

Protocol
General precautions should be taken when setting up a PCR, including setting up the reaction on ice, adding polymerase last, gentle pipetting, thorough mixing and a quick centrifugation. The following procedure can be used as a guideline. Reactions may need to be optimized individually.

Reaction setup (for 50 µl)

Total reaction volume can be adjusted as needed.

Typical cycling conditions

Notes:

5x VeraSeq Buffer II should be used as the default buffer for high-fidelity amplification. For GC-rich and difficult templates, use 5x VeraSeq GC Buffer. VeraSeq 2.0 High-Fidelity DNA Polymerase stalls on uracil residues in the template strand and prevents further extension. Therefore, dUTP should not be used in the reaction. If DNA templates contains uracil or dUTP needs to be incorporated, use VeraSeq ULtra (cat. no. P7520L). A final concentration of 0.2 µM is recommended for each primer, but it can be varied in the range of 0.2–1 µM.

Recommended template quantities:

One unit is usually sufficient for amplifying most targets. For long targets (>1 kb), difficult templates or to increase yield, it may be necessary to add up to 2 units of enzyme. Both 5x VeraSeq Buffer II and GC buffer are formulated to provide a final 1x concentration of MgCl₂ of 1.5 mM. In cases where additional Mg^₂+ is required, adjust the final Mg^₂+ concentration in 0.2 mM steps.

For GC rich templates, DMSO may be used to reduce the secondary structure of complex templates. DMSO is generally used at a 3% final concentration (v/v). If additional optimization is required, adjust the concentration in 1–2% increments (2–9% in final reaction). The primer annealing temperature should be lowered to account for the presence of the solvent. VeraSeq 2.0 High-Fidelity DNA Polymerase is also compatible with other PCR-enhancing additives, such as BSA and betaine.

Quality control analysis

Specific activity was measured using a twofold serial dilution method. Dilutions of enzyme were made in 1x reaction buffer and added to 50 µL reactions containing activated calf thymus DNA; 25 mM TAPS (tris-[hydroxymethyl]-methyl-amino-propanesulfonic acid, sodium salt), pH 9.3 at 25°C; 50 mM KCl; 2 mM MgCl₂; 1 mM β-mercaptoethanol; 200 µM each dATP, dGTP, dTTP; and 100 µM [3H]-dCTP (0.075 Ci/mmole). Reaction vessels were mixed and incubated at 74°C for 10 minutes.

Protein concentration is determined by OD₂₈₀ absorbance.

Physical purity is evaluated by SDS-PAGE of concentrated and diluted enzyme solutions followed by silver-stain detection. Purity is assessed by comparing the aggregate mass of contaminant bands in the concentrated sample to the mass of the band corresponding to the protein of interest in the diluted sample.

Double-stranded endonuclease activity is determined in a 50 µL reaction containing 0.5 µg of plasmid DNA and 10 µL of enzyme solution incubated for 4 hours at 37°C.

E. coli contamination is evaluated using 5 µL replicate samples of enzyme solution that are denatured and screened in a TaqMan qPCR assay for the presence of contaminating E. coli genomic DNA using oligonucleotide primers corresponding to the 16S rRNA locus.

This enzyme is not recommended for NGS workflows: for NGS use 2x HiFi PCR Master Mix 2.0 (cat. no. P7670).

• High-fidelity applications. This enzyme is not recommended for NGS workflows: for NGS use 2x HiFi PCR Master Mix 2.0 (cat. no. P7670).
• Long amplification
• Cloning
• Synthetic biology